Tools For Tiling

For fixing clay tiles, a plumb line and soul level are required for setting out the lines to genuine verticals and horizontals; some thin wooden secures are expected to help the most minimal tile pushes as work advances; a scored tile glue spreader, a tile shaper, a couple of pliers and a wipe are likewise vital. A tile-culting dance will accelerate cutting straight lines; a tile saw can cut bends. Utilize a sharp blade for cutting plug tiles; a couple of scissors or cuts for metallic tiles; a glass shaper for reflect tiles and a block support and club hammer for squeezed impersonation block and stone tiles if essential.

Finding the level

The subsequent stage is to set up a precisely level datum line around the room. Never trust an evading board to be level more than likely utilizing an avoiding board as a level will imply that flat columns won’t be really even, and as tiling is finished by coming back to the beginning stage the lines won’t line up.

Imprint a line on the divider directly round the stay with a board and a soul level, to agree with the base edge of the least line of entire tiles. Along this line pin thin secures to the divider with workmanship nails; don’t drive the nails home, since the strips should be prised off once more. In the event that nails can’t be crashed into the divider (an old tile divider, state) get the strips flat by putting them on little piles of tiles. Next, utilizing a soul level or plumb line, draw a genuine vertical line on the divider at where tiling is to begin – at the edge of the last vertical line of entire tiles (on a solid divider) or corresponding with the primary line of entire tiles close by a window or entryway opening. A vertical secure can be nailed along this vertical line as an additional guide.

Fixing the tiles

Spread the tile glue on the divider with a scored spreader, covering a territory of around each square meter in turn. Draw the spreader over the cement by squeezing it down with the goal that the teeth contact the mortar surface underneath; the scores at that point guarantee that the cement is spread to a standard profundity. Spot the principal tile on the level secure, line its edge up with the vertical rule and press it tenderly however immovably to the divider. Include the following tile nearby the first, with the spacer carries simply contacting, and watch that its face is level with that of the principal tile. In the event that the tiles don’t have spacer drags, use matchsticks or tile spacers between the tiles. Proceed with the line until the edge of the zone is come to, at that point include a second, third and fourth column, checking constantly that the tiles are precisely lined up with one another. Spread increasingly cement along the territory over the divider secure, proceeding to include entire tiles until the region is secured or until a check, for example, an entryway or window ledge is come to. From lime to time, utilize a soul level on a strip to watch that the tiles are genuinely even.

Cutting tiles

At a window ledge, it is common to tile the uncovers and the ledge itself with round-edged or coated edged tiles which cover the edges of the tiles on the substance of the divider. So the following employment is to stamp and sliced the bits of tile to go on the divider underneath the window ledge. Imprint the tile with a felt pen or Chinagraph pencil, and afterward score กระเบื้องสระว่ายน้ำ the coated essence of the tile with a tile shaper. To snap the tile along the scored line, either push down on cither side of the line over a straight edge, or utilize a couple of tile snappers with calculated jaws. On the off chance that the cut edge is unpleasant, utilize a tile scouring stone (a kind of coarse rough taking after pumice stone) or an oilstone hosed with water to smooth the tile edges. To cut a L-shape, make one cut with a tile saw and the other with a tile shaper. Cut and fit the thin bits of tile that outline the window opening; at that point fit the round-edged tiles inside the uncover, butting the round edge flawlessly over the edges of the cut pieces on the substance of the divider. Complete the tiling of the uncovers with entire tiles or cut pieces as fundamental.

Leave a Reply

Your email address will not be published. Required fields are marked *